• 888-750-4777
  • This email address is being protected from spambots. You need JavaScript enabled to view it.
Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1
  • 2

TOPIC: electrical

electrical 13 years 10 months ago #36663

A couple times per week I will note #10 wire to a forty amp breaker, I will recommend a licenced elect. eval.I do this based on the understanding that #8 wire is always (rope type)or( stranded)So when I see the solid copper wire it screams wrong to me.I see this situation in both- new,& -older homes. It seems odd that brand new construction with recent APPROVED labels on them would be incorrect.... In what ? if any? situations does this become good enough to walk past ? Thank You.

Please Log in to join the conversation.

Re: electrical 13 years 10 months ago #36664

I believe that this can be acceptable for an appliance like an air conditioner. The data plate on the air conditioner exterior condensor states the wire minimum ampacity.

This is old from the 2003 IRC

IRC 2003, E3602.11 Branch circuits for air-conditioning and heat pump equipment. The ampacity of the conductors supplying multi motor and combination load equipment shall not be less than the minimum circuit ampacity marked on the equipment. The branch-circuit overcurrent device rating shall be the size and type marked on the appliance and shall be listed for the specific purpose.

Please Log in to join the conversation.

Home Safe Home Inspections
Link Url: Cleveland Home Inspector - www.hshinspections.net/
Body:Performing Home Inspections in Cleveland, Parma, Brecksville, Broadview Heights, North Royalton, Strongsville and surrounding areas.
Keywords:Parma,Broadview...

Re: electrical 13 years 10 months ago #37042

  • Bill Warner
  • Bill Warner's Avatar
  • Offline
  • Elite Member
  • Elite Member
  • There's a fine line between comedy and humor...
  • Posts: 269
  • Karma: 1
  • Thank you received: 1
David nailed it. 
Most 40A breakers I run across are typically controlling HVAC equipment.  You would have to look at the data tag on the HVAC unit to determine the minimum ampacity circuit rating and the maximum allowable amp rating for the overcurrent protection device.  If you look at the next data tag you come across, you will see they are different and don't necessarily match wire size to breaker amperage.

If you look at the photo I attached, the data tag indicates Minimum circuit amps at 23.6A (which would be 12ga conductor) and Maximum Fuse or HVACR breaker rating at 40A.  This is what you must base your assessments upon of the breakers and conductors in the panel.  In this case, if you called out a 12ga conductor on a 40A breaker protecting the air conditioner... you would be incorrect in calling it out.
Attachments:

Please Log in to join the conversation.

Bill Warner
Dayton Infrared Thermal Inspection
DaytonThermalInspection.com
Infrared Thermal Imaging Inspections Serving Dayton, Cincinnati, and Greenville Ohio
For a Link Exchange please This email address is being protected from spambots. You need JavaScript enabled to view it. your info

Re: electrical 13 years 9 months ago #37458

That does not compute Bill. Help me understand? Why would they allow 12g wire and then allow 40a breaker? There is no way that would support the load and the wire would glow before the breaker tripped.

WIres should be sized to handle the amp ratings shouldn't they?

Please Log in to join the conversation.

Knoxville TN Home Inspector
Fogarty Home Inspection Services
Professional mold and radon testing of east Tn
Professional home and commercial inspections of Knoxville
www.homeinspectorknoxville.com
Title: Home Inspector Knoxville
Meta Keywords- Knoxville home inspection, Oak Ridge TN home inspector,...

Re: electrical 13 years 9 months ago #37472

  • Bill Warner
  • Bill Warner's Avatar
  • Offline
  • Elite Member
  • Elite Member
  • There's a fine line between comedy and humor...
  • Posts: 269
  • Karma: 1
  • Thank you received: 1
It boils down to cost Sean.

The primary reason for the allowance with A/C units is that the sustainable load while the unit is operating will never reach 40amps... it may surge upon start-up near that, but the sustainable load will be around the minimum ampacity rating on the data tag.

Please Log in to join the conversation.

Bill Warner
Dayton Infrared Thermal Inspection
DaytonThermalInspection.com
Infrared Thermal Imaging Inspections Serving Dayton, Cincinnati, and Greenville Ohio
For a Link Exchange please This email address is being protected from spambots. You need JavaScript enabled to view it. your info

Re: electrical 9 years 3 months ago #61433

I think the problem with this is as HVAC units age they tend to draw more amps plus if a compressor or condensing fan seizes
for a short time you could be cooking your 12 gage. 

Please Log in to join the conversation.

  • Page:
  • 1
  • 2
Time to create page: 0.208 seconds
© 2004-2024 Home Inspector Pro Inc. All Rights Reserved.